Cisco 400-151 Braindumps

Question: 16

Within an ACI fabric, a routing protocol is needed to assist with route redistribution between the outside networks and the internal fabric. Which routing protocol is needed to run in the fabric at location 1 to allow the VM access to the networks advertised by the external Layer 3 network.

A. eBGP
B. OSPF
C. MP-BGP
D. iBGP
E. IS-IS

Answer: C

Question: 17

How do you manually configure a vNIC MAC address?

A. Use the mac -address-table static command.
B. Modify the dynamic vNIC connection policy.
C. Use the set identity dynamic-mac command.
D. Modify the adapter policy.

Answer: D

Question: 18

Which two statements about import and export route control in an ACI fabric are t rue? (Choose two.)

A. Prefixes learned from OSPF/EIGRP L30urs are never permitted inbound by default.
B. Prefixes learned from BGP L3outs cannot be filtered inbound.
C. Export route control controls if the prefixes are redistributed from MP-BGP to the egress leaf.
D. Prefixes permitted inbound are redistributed into MP-BGP at the ingress leaf.

Answer: C,D

Cisco 400-151 CCIE Data Center Exam Questions and Dumps

Cisco 400-151 Practice Questions

Question: 12

Which OpenStack project, whose data can be used to provide customer billing, resource tracking, and alarming capabilities across all OpenStack core components, is a component of the telemetry project?

A. Ceph
B. Trove
C. Ceilometer
D. Heat

Answer: C

Question: 13

Which two statements about OpenStack are true? (Choose 2)

A. Horizon is the component that is used for IP address management.
B. Nova is the compute component that is used to manage and automate the provisioning of compute resources.
C. Keystone is the networking component that is used to create and manage network resources.
D. Neutron is the networking component that is used to create and manage network resources.
E. Trove is the GUI web application that is used to control and configure different 0penStack components.

Answer: D,E

Question: 14

Which two connectivity modes does Cisco RISE support? (Choose 2)

A. Directly connected. No virtual port channel is supported.
B. Indirectly connected. Only Layer 3 adjacent.
C. Indirectly connected. Only Layer 2 adjacent
D. Indirectly connected. Layer 2 and Layer 3 adjacent.
E. Directly connected. Virtual port channel is supported.

Answer: C,E

Question: 15

Cisco FabricPath switches support ECMP forwarding for known unicast frames. If the destination switch ID can be reached through more than one output interface with equal cost, the forwarding engine uses a hash function to pick one of the interfaces. Which three options are valid for hash input for unicast frames? (Choose three.)

A. Use only the source parameters (layer-3, layer-4, or mixeD. .
B. Use the FabricPath switch ID in the FabricPath header.
C. Use only the destination parameters (layer-3, layer-4, or mixeD. .
D. Use both the source and the destination parameters (layer-3, layer-4, or mixeD. .
E. Include only Layer 2 input (source or destination MAC address).

Answer: A,C,D

Download Cisco 400-151 CCIE Data Center Exam PDF Questions

Cisco CCIE 400-151 Study Material

Question: 9

Which IETF standard is the most efcient messaging protocol used in an loT network?
A. SNMP
B. HTTP
C. CoAP
D. MQTT

Answer: C

Question: 10

Which two statements about policing, queuing, and scheduling are true? (Choose two.)

A. The WRHD algorithm is reactve approach only to trafc congeston.
B. Policing is the monitoring of data rates for a partcular class of trafc. The device can also monitor associated burst sizes.
C. You can apply weighted random early detecton to a class of trafc, which allows packets to be dropped based on the CoS feld.
D. You can schedule trafc by imposing a maximum data rate on a class of trafc so that excess
packets are dropped.

Answer: B,C

Question: 11

Which three optons are common PTP device types? (Choose three.)

A. ordinary clock
B. network clock
C. crystal clock
D. transparent clock
E. boundary clock
F. sundials

Answer: A,D,E

Cisco CCIE 400-151 Exam Dumps Free Download

 

350-080 Sample Question

Question: 20

Which Ether type is used to identify FIP?

A. 0x8914
B. 0x8906
C. 0x8915
D. 0x8905

Answer: A

350-080 Sample Question

Question: 19

How are IP multicast IGMP entries synchronized between vPC peers?

A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain, and there is no need to synchronize it between vPC peers

Answer: B

350-080 Sample Question

Question: 18

Which three statements best describe multicast operation on Cisco Nexus switches in a data center? (Choose three.)

A. Cisco NX-OS Software does not support PIM dense mode.
B. The command ip multicast-routing must be enabled in Cisco NX-OS Software before any multicast configuration is possible on the switch.
C. PIM CLI configuration and verification commands are not available until you enable the PIM feature with the feature pim command.
D. Cisco NX-OS Software supports multicast routing per Layer 3 VRF instance.
E. The default PIM operational mode on the Cisco Nexus 7000 switch is SSM.

Answer: A,C,D

350-080 Sample Question

Question: 17

To use ERSPAN, which command must be configured in a service profile?

A. capability erspan
B. capability l3 control
C. capability monitor
D. capability session
E. capability span

Answer: B

350-080 Sample Question

Question: 16

In a configuration with redundant supervisors, how many IP addresses are required to configure full remote access via management 0?

A. two IP addresses, one for each supervisor
B. three IP addresses, one virtual IP and one physical IP for each supervisor
C. one IP address that is shared among supervisors
D. none management 0 will use the IP address from the first SVI that is created

Answer : C

350-080 Sample Question

Question: 15

What are the three prerequisites for enabling FCoE on a Cisco Nexus 7000? (Choose three.)

A. M Series module
B. F Series module
C. no-drop QoS policy
D. NPIV feature
E. FCoE module license
F. Fabric Extender configured

Answer: B,C,E

350-080 Sample Question

Question: 14

When creating a role in a Cisco Nexus 7000 Series Switch, rules are used to define the type of operations that a role will allow the user to perform. Which two of these parameters cannot be applied as a rule? (Choose two.)

A. port-profile
B. command
C. access-list
D. feature-group
E. OID

Answer: A,C

350-080 Sample Question

Question NO: 13

FabricPath brings the benefits of routing protocols to layer 2 network Ethernet environments. What are the advantages of using FabricPath technology? (Choose three.)

A. FabricPath provides MAC address scalability with conversational learning
B. Loop mitigation with TTL in the frame field
C. STPl independence
D. 10 Gbps bandwidth
E. Layer 2 extensions between data centers

Answer: A,B,C

350-080 Sample Question

Question NO: 12

350-080 Testinside

Overlay Transport Virtualization (OTV) overlay interface is a logical multi access and multicast-capable interface that must be explicitly defined by the user and where the entire OTV configuration is applied. Which statements are true about OTV overlay interface? (Choose two.)

A. When an OTV edge device receives a Layer 2 frame destined for a remote data center site, the frame is logically forwarded to the overlay interface.
B. The OTV edge device performs the dynamic OTV encapsulation on the Layer 2 packet and sends it to the join interface toward the routed domain.
C. When the OTV edge device receives a Layer 2 frame destined for a remote data center site, the frame is logically forwarded to the join interface.
D. The OTV edge device performs the dynamic OTV encapsulation on the Layer 2 packet and sends it to the overlay interface toward the routed domain.

Answer: A, B

350-080 Sample Question

Question NO: 11

Overlay Transport Virtualization (OTV) join interface is used to source the OTV encapsulated traffic and send it to the Layer 3 domain of the data center network. Which statements are true about OTV join interface? (Choose three.)

A. Join interface is a Layer 3 entity, and with the Cisco NX-OS release 6.0, it can only be defined as a physical interface, physical subinterface, Layer 3 port channel, or Layer 3 port channel subinterface.
B. A single join interface can be defined and associated with a given OTV overlay.
C. Multiple overlays can also share the same join interface.
D. Join interface can be a loopback interface.
E. The join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.

Answer: A, B, C

350-080 Sample Question

Question NO: 10

What is the mechanism that is used to allocate MAC addresses that are assigned to the VDC for
the system MAC address?

A. NX-OS uses a random MAC address from the IEEE OUI block that is assigned to Cisco.
B. The VDC system MAC is pulled from the active supervisor and concatenated through a hash to
ensure uniqueness.
C. NX-OS uses a value that is based on a range that is assigned to the SPROM of the system
backplane.
D. The VDC system MAC is based on a range that is allocated to the first line card that is installed
in the switch.

Answer: C
Explanation: